지원사업
학술연구/단체지원/교육 등 연구자 활동을 지속하도록 DBpia가 지원하고 있어요.
커뮤니티
연구자들이 자신의 연구와 전문성을 널리 알리고, 새로운 협력의 기회를 만들 수 있는 네트워킹 공간이에요.
논문 기본 정보
- 자료유형
- 학술저널
- 저자정보
- 발행연도
- 2022.8
- 수록면
- 548 - 555 (8page)
이용수
이 논문의 연구 히스토리 (2)
- 이 논문의 후속연구가 궁금하신가요?
- 연관 학술논문 또는 학술발표를 통해 보다 발전된 연구결과를 확인하실 수 있습니다.
- 이 논문의 연구 히스토리 확인하기
초록· 키워드
오류제보하기
Purpose : The purpose of this study is to compare flexural strength according to the thickness of provisional restoration materials manufactured by substactive and additive methods using CAD-CAM system.
Materials and methods : It was divided into three groups with different manufacturing methods, the CON group manufactured by the traditional method, the MIL group manufactured by subtractive methods and the DLP group manufactured by additive methods. Each group was divided into 3 groups by varying the thickness of the specimen (1.0 mm, 1.5 mm, 2.0 mm), and a total of 9 experimental groups were set. Fifteen specimens for each group were prepared in the form of a bar and the flexural strength was measured.
Results : According to the manufacturing method, the MIL group showed the highest flexural strength, followed by the DLP group and the CON group(p<0.01). In the MIL and DLP groups, the flexural strength increased statistically significantly as the thickness increased (p<0.01), but in the CON group, there was no statistically significant difference in the flexural strength at 1.5 mm thickness and 2.0 mm thickness(p>0.05).
Conclusion : Provisional restorative resins fabricated by subtractive methods showed higher flexural strength than those made by additive manufacturing, and both showed superior flexural strength than those fabricated by traditional methods. Active use of the CAD-CAM system in the dental field is recommended, however, as the flexural strength decreases statistically as the thickness of the material decreases, we need to be careful about reduction in the thickness of the material.
Materials and methods : It was divided into three groups with different manufacturing methods, the CON group manufactured by the traditional method, the MIL group manufactured by subtractive methods and the DLP group manufactured by additive methods. Each group was divided into 3 groups by varying the thickness of the specimen (1.0 mm, 1.5 mm, 2.0 mm), and a total of 9 experimental groups were set. Fifteen specimens for each group were prepared in the form of a bar and the flexural strength was measured.
Results : According to the manufacturing method, the MIL group showed the highest flexural strength, followed by the DLP group and the CON group(p<0.01). In the MIL and DLP groups, the flexural strength increased statistically significantly as the thickness increased (p<0.01), but in the CON group, there was no statistically significant difference in the flexural strength at 1.5 mm thickness and 2.0 mm thickness(p>0.05).
Conclusion : Provisional restorative resins fabricated by subtractive methods showed higher flexural strength than those made by additive manufacturing, and both showed superior flexural strength than those fabricated by traditional methods. Active use of the CAD-CAM system in the dental field is recommended, however, as the flexural strength decreases statistically as the thickness of the material decreases, we need to be careful about reduction in the thickness of the material.
목차
ABSTRACT
Ⅰ. 서론
Ⅱ. 재료 및 방법
Ⅲ. 결과
Ⅳ. 고찰
Ⅴ. 결론
참고문헌
참고문헌 (0)
참고문헌 신청함께 읽어보면 좋을 논문
논문 유사도에 따라 DBpia 가 추천하는 논문입니다. 함께 보면 좋을 연관 논문을 확인해보세요!
-
Comparison of Flexural Strength of Three-Dimensional Printed Three-Unit Provisional Fixed Dental Prostheses according to Build Directions
Journal of Korean Dental Science
2019 .06
-
치과 CAD/CAM 가공방식에 따른 임시보철물의 내면 적합도 : 3차원 중첩 분석
대한치과기공학회지
2019 .01
-
제작방법에 따른 임시 수복용 레진의 파절강도 및 굴곡강도에 관한 연구
대한치과보철학회지
2019 .01
-
미세입자 분사마모 표면처리가 Fiber-Reinforced Composite 포스트의 굴곡 강도에 미치는 영향
구강회복응용과학지
2016 .03
-
CAD/CAM 세라믹의 두께가 색조에 미치는 영향
한국치위생학회지
2016 .01
-
우식에 이환된 유전치용 3D 프린팅 레진 전장관의 두께에 따른 파절강도 및 반투명도 평가
대한구강보건학회지
2023 .03
-
Effect of Coloring Agent on the Strength and Transmittance of Dental Zirconia Block
International Journal of Clinical Preventive Dentistry
2017 .01
-
치과 CAD/CAM용 지르코니아의 소결 시 계류시간이 굴곡강도에 미치는 영향
대한치과재료학회지
2016 .06
-
Comparison of fracture strength after thermo-mechanical aging between provisional crowns made with CAD/CAM and conventional method
The Journal of Advanced of Prosthodontics
2020 .01
-
절삭 및 적층 가공법으로 제작된 3본 고정성 국소의치의 변연 및 내면 적합도에 관한 연구
대한치과보철학회지
2020 .01
-
Influence of heating rate on the flexural strength of monolithic zirconia
The Journal of Advanced of Prosthodontics
2019 .01
-
Evaluation of marginal and internal gap of three-unit metal framework according to subtractive manufacturing and additive manufacturing of CAD/CAM systems
The Journal of Advanced of Prosthodontics
2017 .01
-
Evaluation of marginal discrepancy of pressable ceramic veneer fabricated using CAD/CAM system: additive and subtractive manufacturing
The Journal of Advanced of Prosthodontics
2018 .01
-
치과 CAD-CAM용 하이브리드 수복재의 일축/이축 굽힘강도 및 신뢰성
대한치과재료학회 학술대회
2015 .04
-
Impact of ZrO2 nanoparticles addition on flexural properties of denture base resin with different thickness
The Journal of Advanced of Prosthodontics
2021 .08
-
절삭 및 적층 가공 방법으로 제작된 작업 모형의 정확도 비교
대한치과재료학회지
2018 .03
-
치과용 복합레진의 3점/4점 굽힘 시험법에 의한 굽힘강도 특성 평가
대한치과재료학회 학술대회
2015 .04
-
적층가공을 이용한 임시의치 제작 및 기존방식의 임시의치와의 비교 증례
대한치과보철학회지
2019 .01
-
Influence of surface treatments and repair materials on the shear bond strength of CAD/CAM provisional restorations
The Journal of Advanced of Prosthodontics
2019 .01
-
고정성 임시 보철물 재료의 색 안정성에 대한 절삭 및 적층가공법의 비교평가
구강회복응용과학지
2021 .06
이 논문의 저자 정보
이 논문과 함께 이용한 논문
치과 임플란트 가이드 3D 프린팅의 품질 평가를 위한 디지털 트윈 방법론
임주현
,
윤병동
한국정밀공학회 학술발표대회 논문집
2023
.05
광경화성 액상수지경화방식을 이용한 치과용 3D 프린터 종류와 특성
문원준
,
Enshi Jiang
,
최유경
외 2명
대한치과의사협회지
2023
.06
3차원 프린팅 및 절삭가공 방식으로 제작된 4Y-TZP의 표면 특성 및 전단결합강도에 대한 비교 연구
경규영
,
곽재영
,
김성균
외 2명
대한치과재료학회지
2023
.03
의료용 폴리머 소재를 활용한 3D 프린팅 인공치아용 사면체 비정질 카본 코팅 기술 연구
장영준
,
김종국
,
신창희
외 1명
Tribology and Lubricants
2022
.12
최근 본 자료
댓글(0)
0